Announcement

Collapse
No announcement yet.

Problème check_nrpe/Nsclient++

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Problème check_nrpe/Nsclient++

    Bonjour,
    j'éssai de faire fonctionner NRPE sur des machine serveur 2003.
    J'ai installé NSclient++ qui fonctionne avec les check_nt.
    Sur ma machine Nagios je tape :
    ./check_nrpe -H 10.20.0.61 -p 5666 -c test
    Et j'ai une erreur qui s'affiche: NRPE_NT failed to create process, exiting...
    Je ne comprend pas le message le script est simple et correcte pourtant !:confused:

    Script ok.bat:

    @echo OK: Everything is going to be fine
    @exit 0


    Config NSclient++:

    [modules]
    ;# NSCLIENT++ MODULES
    ;# A list with DLLs to load at startup.
    ; You will need to enable some of these for NSClient++ to work.
    ; ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
    ; * *
    ; * N O T I C E ! ! ! - Y O U H A V E T O E D I T T H I S *
    ; * *
    ; ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
    FileLogger.dll
    CheckSystem.dll
    CheckDisk.dll
    NSClientListener.dll
    NRPEListener.dll
    SysTray.dll
    CheckEventLog.dll
    CheckHelpers.dll
    ;
    ; CheckWMI IS AN EXTREM EARLY IDEA SO DONT USE FOR PRODUCTION ENVIROMNEMTS!
    ;CheckWMI.dll
    ;
    ; RemoteConfiguration IS AN EXTREM EARLY IDEA SO DONT USE FOR PRODUCTION ENVIROMNEMTS!
    ;RemoteConfiguration.dll

    [Settings]
    ;# OBFUSCATED PASSWORD
    ; This is the same as the password option but here you can store the password in an obfuscated manner.
    ; *NOTICE* obfuscation is *NOT* the same as encryption, someone with access to this file can still figure out the
    ; password. Its just a bit harder to do it at first glance.
    ;obfuscated_password=
    ;
    ;# PASSWORD
    ; This is the password (-s) that is required to access NSClient remotely. If you leave this blank everyone will be able to access the daemon remotly.
    ;password=secret-password
    password=
    ;
    ;# ALLOWED HOST ADDRESSES
    ; This is a comma-delimited list of IP address of hosts that are allowed to talk to the all daemons.
    ; If leave this blank anyone can access the deamon remotly (NSClient still requires a valid password).
    ; The syntax is host or ip/mask so 192.168.0.0/24 will allow anyone on that subnet access
    allowed_hosts=10.x.x.x
    ;
    ;# USE THIS FILE
    ; Use the INI file as opposed to the registry if this is 0 and the use_reg in the registry is set to 1
    ; the registry will be used instead.
    use_file=1

    [log]
    ;# LOG DEBUG
    ; Set to 1 if you want debug message printed in the log file (debug messages are always printed to stdout when run with -test)
    debug=1
    ;
    ;# LOG FILE
    ; The file to print log statements to
    file=NSC.log
    ;
    ;# LOG DATE MASK
    ; The format to for the date/time part of the log entry written to file.
    date_mask=%Y-%m-%d %H:%M:%S


    [NSClient]
    ;# ALLOWED HOST ADDRESSES
    ; This is a comma-delimited list of IP address of hosts that are allowed to talk to NSClient deamon.
    ; If you leave this blank the global version will be used instead.
    allowed_hosts=10.x.x.x
    ;# NSCLIENT PORT NUMBER
    ; This is the port the NSClientListener.dll will listen to.
    port=1248
    ;
    ;# BIND TO ADDRESS
    ; Allows you to bind server to a specific local address. This has to be a dotted ip adress not a hostname.
    ; Leaving this blank will bind to all avalible IP adresses.
    bind_to_address=


    [Check System]
    ;# CPU BUFFER SIZE
    ; Can be anything ranging from 1s (for 1 second) to 10w for 10 weeks. Notice that a larger buffer will waste memory
    ; so don't use a larger buffer then you need (ie. the longest check you do +1).
    CPUBufferSize=1h
    ;
    ;# CHECK RESOLUTION
    ; The resolution to check values (currently only CPU).
    ; The value is entered in 1/10:th of a second and the default is 10 (which means ones every second)
    CheckResolution=10

    [NRPE]
    ;# NRPE PORT NUMBER
    ; This is the port the NRPEListener.dll will listen to.
    port=5666
    ;
    ;# COMMAND TIMEOUT
    ; This specifies the maximum number of seconds that the NRPE daemon will allow plug-ins to finish executing before killing them off.
    command_timeout=60
    ;
    ;# COMMAND ARGUMENT PROCESSING
    ; This option determines whether or not the NRPE daemon will allow clients to specify arguments to commands that are executed.
    allow_arguments=0
    ;
    ;# COMMAND ALLOW NASTY META CHARS
    ; This option determines whether or not the NRPE daemon will allow clients to specify nasty (as in |`&><'"\[]{}) characters in arguments.
    allow_nasty_meta_chars=0
    ;
    ;# USE SSL SOCKET
    ; This option controls if SSL should be used on the socket.
    ;use_ssl=1
    ;
    ;# BIND TO ADDRESS
    ; Allows you to bind server to a specific local address. This has to be a dotted ip adress not a hostname.
    ; Leaving this blank will bind to all avalible IP adresses.
    bind_to_address=
    ;
    ;# ALLOWED HOST ADDRESSES
    ; This is a comma-delimited list of IP address of hosts that are allowed to talk to NRPE deamon.
    ; If you leave this blank the global version will be used instead.
    allowed_hosts=10.x.x.x
    ;
    ;# SCRIPT DIRECTORY
    ; All files in this directory will become check commands.
    ; *WARNING* This is undoubtedly dangerous so use with care!
    script_dir=C:\NSClient\scripts\


    [NRPE Handlers]
    ;# COMMAND DEFINITIONS
    ;# Command definitions that this daemon will run.
    ;# Can be either NRPE syntax:
    test=critical.bat

  • #2
    J'ai trouvé un faut mettre le chemin complé du script soit:

    [NRPE Handlers]
    test=C:\NSClient\scripts\critical.bat.

    C'est béte mais bon ...

    Comment

    Working...
    X